Syphons, Transfer Hose & Clamps

This Large Syphon features a blow lung pump and a tapered butterfly tap, designed for efficient and controlled dispensing. Its robust construction ensures durability, making it ideal for various liquid applications. The butterfly tap allows precise flow control, enhancing ease of use and minimising spills. Perfect for both professional and home settings where reliable liquid handling is essential.

The Eco syphon kit from Ferrari, with two metres of 10mm internal diameter wine transfer hose. Racking by syphon leaves the lees sitting in the bottom of the vessel, which is the whole point of doing it that way.

A cheap bit of kit that saves a lot of mess. Check that 10mm suits the taps and fittings you already have. Stocked at Laverton North and Epping.

- Transfer beer, wine, cider and spirits between vessels without the hassle of starting a siphon.
- Place your receiving vessel side-by-side or even above the transferring vessel.
- Perfect for transferring between primary and secondary fermenter, or from fermenter to bottling bucket or keg.
- Reduce excess oxygen exposure caused by hand-pumping or blowing into a carboy hood to start a siphon.

1/2 Inch BSP Super Sucker Self Priming Siphon Transfer Pump

The Super Sucker transfer pump is the quickest, most hassle-free solution to moving beer, wine, cider or spirits between vessels. Rack from the primary fermenter to secondary or from carboy to keg without the excess oxygen exposure that results from hand-pumping a siphon or blowing into a carboy hood.

Simply run transfer tubing from a racking cane to the pump and then to your receiving vessel, flip the switch, and let the Super Sucker do the work while you kick back and enjoy a cold one.

With the Super Sucker you don't need gravity or CO2 pressure to move liquid around. Thanks to the pump's considerable max lift height, you can leave your heavy, full fermenter on the ground and place the receiving keg or carboy side-by-side or even above the fermenter on a countertop.

The 1/2 Inch BSP inlet and outlet are perfect for use with 1/2 Inch push in fittings such as:

• monotight - 6.35mm (1/4") x 1/2" Female Thread
• monotight - 8mm (5/16") x 1/2" Female Thread
• duotight - 9.5mm (3/8") Female x 1/2" Female Thread

It is important to remember to clean thoroughly and store dry to avoid potential sites of infection. We would recommend flushing/recirculating with a diluted mix of StellarSan for at least 2 minutes of contact time prior to using this pump.

Features:

• Self-Priming
• 1/2 Inch BSP Inlet/Outlet
• On/Off Switch
• Max Flow: 4.23 L/min
• Suction: 127mm
• Max Lift: 3.8m
• Maximum Temperature: 60°C
• Pressure: 90 psi
• Voltage: 12V DC (3.5A)
• Power Cord Length: 1.2m
• Power Adaptor Cord Length: 70cm
• Power Switch Cord: 25cm

Compare every wine pump and transfer pump we stock.

This Throttle Flow Stop Valve is designed for use with syphon systems and fits an 8mm internal diameter hose. It allows precise control of fluid flow, helping to regulate and stop the flow as needed. Made with reliable materials, it ensures durability and consistent performance in various applications. Ideal for maintaining efficient and safe operation in your syphon setup.

A hose clip for 8mm tube or PVC hose, listed by Ferrari under reference 16540. It is the small clamp that stops a racking line popping off halfway through a transfer, which is a mess nobody wants twice.

Sized for 8mm hose. Measure the internal diameter of the line you are using before ordering.

Hose in 64mm diameter. This listing carries the diameter only, with no material, wall thickness or length recorded on the page. Rather than send you something that does not suit, tell us what the line will carry and the run length you need, and we will confirm the spec and price. Cut lengths are available through Laverton North and Epping.

A super clamp with a 26 to 28mm clamping range, for small to mid bore hose. Built heavier than a standard worm drive clamp, which is what you want holding a line that has a pump behind it. Measure the outside diameter of the hose once it is seated on the fitting and check it lands inside the 26 to 28mm range before you order.

Hose in 75mm diameter. Only the diameter is recorded on this listing, with no material, wall thickness or length shown. Rather than have you order blind, tell us what you are moving and the length you need and we will confirm the spec and the price. Cut lengths are available through Laverton North and Epping.

Hose in 50mm diameter. The listing records the diameter only, with no material, wall thickness or length shown on the page. Tell us what the line is carrying and how long a run you need and we will confirm the full spec and the price before you order. We can cut to length at Laverton North or Epping.

A super clamp with a 60 to 63mm clamping range, for mid size transfer hose. Heavier construction than a standard worm drive clamp, which matters once there is pressure in the line. Measure the outside diameter of your hose with the fitting seated inside it and check the figure falls inside the 60 to 63mm range before ordering. We carry other sizes if it does not.

A super clamp with an 86 to 91mm clamping range, sized for larger transfer hose. Built heavier than a standard worm drive clamp, which is what you want when there is a pump behind the line. Measure the outside diameter of the hose with the fitting seated inside, then check it falls within the 86 to 91mm range before ordering.

A super clamp with a 113 to 121mm clamping range, sized for the larger hose used on transfer and must lines. Solid clamping beats hope when a pump is running. Measure the outside diameter of your hose with the fitting inside it, and check that figure falls inside the 113 to 121mm range. We stock the smaller sizes too if yours comes up short.

A super clamp with a 31 to 34mm clamping range, for holding hose onto a barb or tail securely. Heavier duty than a standard worm drive clamp and worth it on anything carrying pressure. Measure the outside diameter of your hose once it is seated on the fitting, and make sure it lands inside the 31 to 34mm range before you order.

Hose in 38mm diameter. The listing gives the diameter only, with no material, wall thickness or length recorded on the page. Rather than guess, tell us what you are moving and the length of run you need and we will confirm the spec and price. Available through Laverton North and Epping, and we can cut to length for you.

A worm drive hose clamp with a 9 to 12mm clamping range, for small bore lines. Tightens with a screwdriver and holds better than a cable tie ever will on anything under pressure. Measure the outside diameter of your hose once it is over the barb, and make sure that figure sits inside the 9 to 12mm range before you order.