Measuring Flasks & Glassware

A round laboratory tripod stand, 13cm across and 20cm high. Steady three legged support for a flask or beaker over a heat source, and far less prone to wobble than a makeshift arrangement. Gauze mat and heat source are not included. Check that your vessel sits comfortably within the 13cm ring before ordering, and ask us if you need a taller stand.

A three prong laboratory clamp with cork lined jaws, in the economy version. The cork facing grips glassware without chewing it up, which is the whole point of using a proper clamp. It needs a boss head and stand, which are not included here. Check what your existing stand takes before ordering, and ask us if you are putting a bench together from scratch.

A triangular tripod stand, 12cm wide and 22cm high. The steady base you sit a gauze and a flask on over a heat source at the bench. A simple bit of kit that is hard to improve on. Check the 22cm height clears whatever burner or hotplate you are working over before you order.

A pipette brush, 320mm long with an 8mm head, for cleaning out pipettes and narrow glassware where nothing else will reach. The middle measurement has dropped off this listing, so ask us for the full dimensions if the exact size matters for your glassware. Stocked at Laverton North and Epping.

A large retort stand from La Lidia, with a heavy blue base measuring 310mm and a 700mm rod. The weight in the base is the whole point, since a light stand tips the moment you clamp anything substantial high up the rod. Clamps and bosses are separate items. Check the 700mm rod gives you the working height you need.

A 250ml plastic wash bottle, our economy option. For rinsing glassware and probes down at the bench without pouring from a jug and wearing half of it. The economy line does the same job as the fancier ones for a fraction of the cost, which suits a bench that gets through a few of them. Stocked at Laverton North and Epping.

Measuring Jug 3000mL with In Built Funnel features a stackable design, saving space and keeping your kitchen organized without sacrificing accessibility.

Its inbuilt funnel handle allows for precise measuring and pouring, reducing the need for extra kitchen tools. Embossed graduations and high-quality, break-resistant material ensure accurate measurements, durability, and easy cleaning, ideal for commercial kitchens.

A glass tee piece with an 8cm long span, 8mm diameter pipe and a 2.5 mm measurement listed alongside it. Laboratory glassware for splitting or joining a line where you want to see what is passing through.

The dimensions on this listing are terse, so tell us what you are plumbing it into and we'll confirm it suits before you order.

A glass still splash head in Schott glass from Germany, listed as the base form 3 x 4cm only. The wording on this listing is abbreviated, so it is not fully clear which joints or fittings are included with the base form. Check the measurements and joints on your own glassware and ask us to confirm what you will receive before you order.

A blue pipette filler pump sized to suit 1 to 2ml pipettes. The thumb wheel gives you fine control on small volumes, which is exactly where it matters. It is matched to that pipette range only, so measure the barrel of yours before ordering. We keep the red version for larger pipettes as well if you work across a few sizes.

Orange rubber Ansell teats for Pasteur pipettes, supplied in a pack of 10. Teats perish and split long before the glass does, so having spares in the drawer saves a lot of swearing mid test. They are made for Pasteur pipettes. Check the barrel diameter of the pipettes you are using before ordering, and ask us if you are matching up an unusual size.

A plastic funnel with a 50mm diameter, for decanting into narrow necked bottles and flasks without wearing half of it. Light, cheap and easy to rinse out. No strainer or mesh is listed with it. Check the neck of the vessel you are filling against the 50mm diameter, and ask us if you need a larger funnel or a stainless one instead.

A glass adaptor with a 19/26 cone on one end and a barb tail on the other, listed for the Rankine apparatus. It is the piece that lets you take tubing off a ground glass joint cleanly. It is listed for the Rankine setup and that joint size only. Check the joint on your apparatus before ordering, and ask us if you are matching up an older bench.

A red pipette filler pump sized to suit pipettes from 1ml to 25ml. It draws and dispenses with a thumb wheel, which beats the old approach by a very wide margin. It is matched to that pipette range, so check the barrel of yours before ordering. We keep pipettes and fillers at both Laverton North and Epping if you want to try the fit.

A 1000ml Erlenmeyer flask with a Quickfit 24/29 socket and a flat base, made in Australia. The socket takes matching 24/29 Quickfit glassware, which is sold separately. Glass is glass, so check the joint size on the rest of your setup before ordering. If you are building out a bench and want a hand matching joints, come and see us at Laverton North or Epping.

A 1000ml conical Erlenmeyer flask in NM glass, made in the EU. The standard flask shape for swirling without slopping, which is why brewers use them for yeast starters as well as for bench work. Supplied as the flask alone. The listing title trails off, so ask us if you need the full glass specification before ordering.

Ortho phosphoric acid at 85 per cent, AR grade, supplied in a 2.5 litre container. It is a laboratory reagent stocked for bench work.

All information about this product, including anything to do with its handling, sits with the label and the manufacturer's own documentation. If you need to confirm the grade or the pack size before ordering, get in touch and we will check the stock we hold.

A 3 inch analogue thermometer gauge in stainless steel, reading minus 20 to plus 110, with a 50 mm probe. An analogue face with no battery to go flat on you halfway through a ferment. The 50 mm probe length and the thread on your fitting are the two things to check first. Send us details of the thermowell or fitting you are screwing it into and we will confirm this gauge suits.