Kitchen Equipment

This Italian Giromatic Rotator skewer cooker can be used with a traditional Arrostosini charcoal BBQ. It has and skewers rest and bar Skewer wheel with 23 positions that allow electric rotation by attaching the battery power motor.

This bar properties slow rotation of your skewer, to allow the fat to render out slowly without having the need to turn the skewer. And keep your hand away from the hot cools. Allows you hands-free cooking for a cool beer.

The skewer support flaps work with sewer 10/10 thickness.

Approx. specs 63 x 12 x 90 cm.

Warnings :

• Keep out of reach of children
• Grill not suitable for cooking food
• For use only in open spaces or under the fireplace
• To be used on a flat surface
• Do not handle the channel during its use
• Do not touch the duct during its use to avoid burns
• Do not turn off the cooker with water to avoid corrosion, but allow it to cool in open air
• Be aware of humidity

A CO2 gas distribution board with 6 outputs, letting you run gas to several kegs from the one cylinder. Each output can be managed independently, so you can pour a whole line up of brews with ease. A tidy solution for the growing home bar or keezer.

Code: 129394

This handy tool has numerous dispensing applications:
- The 27mm nut to attach the tap to your font.
- The ring collar that tightens the faucet to the tap shank. 
- The type 30 nut to attach your regulator to your CO2 bottle.
- The FFL fitting to go onto an MFL connection.
- A bottle opener.

• 6kg hopper
• crank handle
• steel mounting board
• Adjustable rollers at both ends to give uniform crush
• 12 TPI knurl to efficiently pull grain through rollers while leaving hull intact to form an excellent filter bed for sparging
• 12mm crank shaft

Prefer us to do the milling? Build your recipe in our grain bill builder and we weigh and mill it to order in store.

A stainless steel bench top drip tray with a slot for your font, keeping your bar area clean and tidy as you pour. It catches the drips and spills so your bench stays spotless and looking sharp. A smart finishing touch for any home draught setup.

A 2 inch sightglass extension kit that lifts your pot or reflux condenser with a quality copper extension, fitting neatly onto the boiler lid. As well as adding height, it lets you run the reflux gin basket in your pot condenser for larger gin batches. Practical, good looking, and a favourite on the gift shelf.

• Sleek, 304-grade stainless steel build
• Includes a standard 4" tri-clamp connection that can be used to connect third-party distilling equipment
• Pressure relief valve for safer distilling
• Can be used as a steam condenser while brewing indoors (when paired with the appropriate equipment)

IMPORTANT NOTES:
The G40 & G70 Distilling Lid is designed primarily for small to medium-sized still heads that do not have heavy, off-centre attachments. The lid is reasonably flexible and is sturdy enough to fit a still head that is within the following specifications:

• A still head height up to 1.1 m (3.6 ft) from the lid.
• A still head weight up to 11 kg (24 lbs), including up to 2 kg (4.4 lbs) of off-centre weight from a swan neck, lyne arm, or
• Condenser running in parallel with the column and offset up to 160 mm (6”) to the main column.
  We recommend external support if:

Your still exceeds the above specifications.
The lyne arm is not vertical but angled or perpendicular running away from the column, resulting in significantly distant off-centre weight.
If the main still head (column) is noticeably leaning.

A large gear, number 8, for the Reber sausage filler, listed for the 5kg and 8kg machines. Gears are what fail when a filler has been leaned on hard with a stiff mix, and a chipped tooth will not get better on its own. It covers those two capacities only. Check the capacity marked on your filler before ordering and we will confirm the part.

A pack of 10 replacement knobs and seals to suit the Black and Decker vacuum bag system. Fresh seals keep your vacuum tight so food stays fresher for longer in the bag. A handy pack of spares to keep your vacuum sealing running smoothly.

Part 35 for the Fabio Leonardi sausage filler: the funnel nut that holds the filling funnel onto the cylinder. Threads take a hammering from constant fitting and washing, and a rounded nut makes a mess of a filling session. Fabio Leonardi part numbers differ between models, so check yours against the diagram or send us a photo before ordering.

The red silicone seal for the piston plate on Trespade sausage fillers in the 3, 5 and 7kg models. The seal is what keeps air behind the plate rather than in your sausages, and once it hardens or tears you will notice the difference straight away.

Confirm your Trespade is one of those three capacities before ordering, and we are happy to check it with you.

A spring loaded foot valve for a bottle filler. The valve stays shut until the wand touches the bottom of the bottle, then opens and fills from below, which keeps splashing and oxygen pickup down. Spring loaded, so it closes the moment you lift out.

Check it against the filler wand you are using, or bring the wand into Laverton North or Epping and we will match it.

A handy 2 inch sightglass adaptor kit that adds a bit of height and a lot of quality to your pot or reflux condenser. The brass adaptor fits straight onto the boiler lid, and it doubles as a way to run the reflux gin basket in your pot for bigger batches. A great shelf item, and a lovely gift for the distiller in your life.

It’s ideal to use If you would like the flavour of your wash to come through.

If you are an Artisan’s that likes make spirits using grains, fruit and much more. This is the right tool to assist you in achieving your projects easy, fast and efficient.

Some of the features of this Pure distilling Pot Copper Condenser are:
    • Fast – 4.5L/hr with alcohol or 2.8L/hr with water
    • With an all copper construction for smoothness of taste
    • It comes with a digital thermometer and is simple to use.
    • Just switch it on and collect your alcohol – it couldn’t be sim
    • Made in Australia

The new version comes with:

• Digital thermometer
• Specialty Rum & Whiskey yeasts
• 2 x 100g sample Barrel Chunks
• Instructions and mounting hardware

Upgrade your RGV slicer with our high-quality replacement blades, designed to handle a wide variety of slicing tasks with ease.

• Serrated Blades: Featuring multiple sharp teeth, these blades are ideal for cutting hard-crusted bread, fibrous foods, tough cuts of meat, and thick cheeses effortlessly.

• Compatibility: Specifically designed for RGV Lucy slicers, but may also be compatible with many other European slicers.

Approximate Dimensions

• Diameter: 200 mm

Customer Notice

Please verify that this product is compatible with your equipment before purchasing. We recommend checking your model specifications to ensure a proper fit.

Made to keep the machines in our meat slicers range cutting cleanly. See all slicer parts and blades.

A cooler bag made for the 30 litre brew fermenter. It wraps the fermenter to hold temperature steady, which matters more than most people expect once the weather turns.

Slips on and off without tools, so you can check the airlock without unwrapping the lot. For the 30 litre fermenter. Measure yours before ordering, and ask us if you are not sure of the fit.